Archives: Shop
Showing 61–72 of 93 results
-
PCL-849A – 4 Port RS-232 Interface Card
174,00 € Excl. VATAdd to cartFeatures PCL-849A:
• Four independent RS-232 serial ports
• Transmission speeds up to 921.6 Kbps (PCL-849)
• Independent I/O addresses, independent/shared IRQ settings
for each of 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, COM4
(PCL-849A/849B/849+)
• Supports surge protection: 3000 VDC (PCL-849B/849+)
• LED indicators on each port indicate data flow
• On-board interrupt status register for greater throughput
• Complete RS-232 modem-control signals
• Supports Windows 95/98/NT/ME/2000, Windows XP, Linux
(ICOM utility), DOS/Windows 3.1Introduction :
The PCL-849 series cards provide four individually configurable
RS-232 serial communication ports. The PCL-849A/849B/849L has a
16C554 UART which makes serial I/O more reliable. The higher
performance PCL-849+ has a 16C654 UART. By buffering data into
64-byte packets before putting it on the bus, UARTs drastically reduce
the CPU load. This makes the PCL-849+ especially suitable for high
speed serial I/O applications under multitasking environments.
The PCL-849 series cards support two operating modes, standard
mode and enhanced mode. In enhanced mode, the address for all four
ports can be set automatically. The PCL-849 series cards also support
either shared IRQ or independent IRQ functions. When an on-board
interrupt occurs, the interrupt status register (vector address) indicates
which port generated it. The shared interrupt can be set to most common
(extended) AT interrupts. This simplifies programming, speeds up
interrupt processing and frees up interrupts for other devices.Specifications PCL-849A :
• Ports: 4 serial ports
• I/O Address Range: from 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12, 15
• Data Bits: 5, 6, 7, 8
• Stop Bits: 1, 1.5, 2
• Parity: none, even, odd
• UARTs: 1 x 16C554 (PCL-849A/849B/849L)
1 x 16C654 (PCL-849+)
• Speed: 50 ~ 921.6 Kbps (PCL-849A)
50 ~ 460.8 Kbps (PCL-849B/849+)
50 ~ 115.2 Kbps (PCL-849L)
• Cables: 30-cm male DB-37 to four male DB-25 (DTE)
• Data Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
• Surge Protection: 3000 VDC (PCL-849B/849+)
2000 VDC (PCL-849L)
• Power Requirements: +5 V @ 250 mA typical, 500 mA max.
±12 V @ 70 mA typical, 120 mA max.
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″)
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage Temperature: -25 ~ 80° C (-13 ~ 176° F) -
PCL-860 – 4 1/2 DIGIT VOLTMETER (Rev A2)
350,00 € Excl. VATAdd to cartIntroduction
The PCL-860 is a 4 1/2 digit DC/AC voltmeter card that plugs into any I/O slot of IBM PC/XT/AT or compatible computers.It provides all the features and accuracy you would expect from a bench-top voltmeter.
It uses the computer screen as its display and it takes one forth of the screen when activated. This size allows 4 separate PC’s instruments (including the PCL-860) display on the screen at same time. In addition, instead of using push-buttons on the instrument front panel,it uses the computer keyboard.The PCL-860 provides a standard programmable DC current source.It can be used as a 4-wire resistance precision ohmmeter. The PCL-860 has also a build-in 16 bit digital output
1.2. Specifications PCL-860
Input impedance 10Mohm
DC voltage
Range Resblution Accuracy200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1Over voltage : 250V DC or peak AC
AC voltage : True RMS
Range Resblution Accuracy
200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1250V DC or peak AC
AC bandwidth :10KHz
Current source : 0.1mA, lmA, 10mA , user defined (< =1OmA)
* Resistance : (4 wire measurement with current source)
Range Resolution Accuracy Current Source20ohm 1 mili-ohm ±0.03% +1 10mA
200ohm 10 mili-ohm ±0.03%+ 1 10mA
2Kohm 0.1ohm ±0.03% +1 lmA
20Kohm lohm ±0.03%+1 0.1mA
* Conversion rate : 2.5, 5, 10 reading/sec
* Digital output : 16 channel TTL compatible 8.0mA sink and 0.4 mA driver
General :
* Power consumption : +5V, 390mA; +12V, 210mA typical* Digital output connecter: 20 pin flat cable connector with +5V, +12V, ground
* I/O base address : &H200-&H3F0 (factory setting is &H230)
* Operating temperature : 0 – 50°C
* Storage temperature : -20 – 65°C
* Weight : 290gm -
PCL-M10 – 3M – Industrial Accelerometer, 80mV/g
252,00 € Excl. VATAdd to cartIndustrial Accelerometer Sensitivity: ±80 mV/g Sensing Range: 1~10kHz Direct connection with WISE-750
-
PCLD – 7216 – I/O MODULE CARR.BORD 16CH.
175,00 € Excl. VATAdd to cartFeatures Optically isolated inputs and outputs between computer and field devices Channel status reflected by on-board LED for easy monitoring On-board fuse protection Specifications
-
PCLD – 774 – Analog Expansion Board
110,00 € Excl. VATAdd to cartFEATURES •Supports all PCL-series DA&C cards •Supports all PCLD-series signal conditioning daughter boards • Up to 4 PCLD-779s can be connected at one time to maximize the temperature measurement capacity •D-37 connector for PCL-814 to interface PCLD-series signal conditioning board • Additional screw terminal block for signal wiring and monitoring • Auto-lock. 20-pin header connectors …
-
PCLD-7115 -WIRING TERM. Board FOR PCL-711
46,00 € Excl. VATAdd to cartDescription: PCLD-7115 DISCONTINUED BY MANUFACTURER WIRING TERMINAL BOARD FOR PCL-711 20 PIN
-
PCLD-782 – OPTO-Isolated D/I Board 16CH
176,00 € Excl. VATAdd to cart16-ch Opto-Isolated Digital Input Board Compatible with all PC-LabCard products with DI channels. See specifications for details. 16 or 24 optically-isolated digital input channels Built-in screw terminals for easy input wiring LEDs indicate input logic status Inputs buffered with voltage comparators
-
PCLD-782B – 24-ch Opto-Isolated Digital Input Board
207,00 € Excl. VATAdd to cart16-ch Opto-Isolated Digital Input Board Compatible with all PC-LabCard™ products with DI channels on either 20-pin flat cable or 50-pin Opto-22 compatible connectors 24 optically-isolated digital input channels Built-in screw terminals for easy input wiring LEDs indicate input logic status Inputs buffered with voltage comparators
-
PCLD-8115 – WIRING TERMINAL Board FOR 818L
104,00 € Excl. VATAdd to cartIndustrial Wiring Terminal Board with CJC Circuit Low-cost screw-terminal boards Onboard CJC (Cold Junction Compensation) circuits for direct thermocouple measurement. Reserved space for signal-conditioning circuits, such as a low-pass filter, and more. Industrial-grade screw-clamp terminal blocks for heavy-duty and reliable connections. Supports PCL-818 series multifunction cards Nylon standoffs, screws and washers included for easy mounting …
-
PCLD-8712 – WIR.TERM.Board PCI-1712/32
152,00 € Excl. VATAdd to cartDIN-rail Wiring Terminal for PCI-1712/L Low-cost screw-terminal with 68-pin SCSI-II connector Reserved space for signal-conditioning circuits such as low-pass filter, voltage attenuator and current shunt Industrial-grade screw-clamp terminal blocks for heavy-duty and reliable connections DIN-rail mounting case for easy mounting Supports PCI-1710U/UL, PCI-1710HGU, PCI-1711U/UL, PCI-1716/L (PCLD-8710) and PCI-1712/1712L (PCLD-8712)
-
PCLD-880 – Industrial TERMINAL Board
108,00 € Excl. VATAdd to cartWiring Terminal Board with Flat Cables and Adapter Pin to pin design Low-cost universal screw-terminal boards for industrial applications 40 terminal points for two 20-pin flat cable connector ports Reserved space for signal-conditioning circuits, such as a low-pass filter, voltage attenuator and c Table-top mounting using nylon standoffs. Screws and washers provided for panel or …
-
PCLD-885 – Relay POWER Board 16 CH.
250,00 € Excl. VATAdd to cart16-ch Power Relay Board Accepts 20-pin or 50-pin (Opto-22 compatible) connectors 16 single-pole single-throw (SPST) relays High-power relay handles up to 5 A @ 250 VAC Onboard varistors protect all relay contact points Industrial screw terminals for ease of wiring LED status indicators +5 V/+12 V power/status LED indicator
