Archives: Shop
Showing 49–60 of 75 results
-
PCL-847A – 4 Port RS-422/485 Card
180,00 € Excl. VATAdd to cartFeatures PCL-847A :
• Four independent RS-422/485 serial ports
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS control PCL-847AIntroduction:
PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires.Specifications PCL-847A :
• Ports: 4
• UART: 4 x 16C550 with 16-byte FIFO
• Speed: 50 ~ 921.6 Kbps
• Parity: none, even, odd
• Signal support:
TxD+, TxD-, RxD+, RxD-, CTS+, CTS-, RTS+ and RTS-
• I/O address: From 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Isolation voltage: 1000 VDC (PCL-846A/846B only)
• Surge protection: 3000 VDC (PCL-846B/847B)
• Power consumption: +5 V @ 250 mA typical, 500 mA max.
• Cables: 30-cm male DB-37 to four male DB-9 (DTE)
• Operating temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage temperature: -25 ~ 80° C (-13 ~ 176° F)
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″) -
PCL-847B – 4 Port RS-422/485 Card SurgeP
230,00 € Excl. VATAdd to cartFeatures PCL-847B:
• Four independent RS-422/485 serial ports PCL-847B
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS controlIntroduction PCL-847B:
PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.
An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires. -
PCL-848A – IEEE-488 CONTROLLER
277,00 € Excl. VATAdd to cart-
General Information PCL-848A
- Introduction to the Product PCL-848A
The PCL-848A/B IPSE-488 interface card is a valuable addition to your PC that allows you to communicate with over 2000 products, made by over 200 manufacturers, in over 14 countries. The IEEE- 488-1978 standard that this IEEE-488 card implements is the most widely used international standard for information transfer between computer and electronic instruments. There are numerous publications and articles that may be used in conjunction with this manual to assist you to understand the interface standard. The IEEE reference document may be ordered by writing to the IEEE Service Center, 445 Hoes Lane, Piscataway, NJ 08854, USA.
The IEEE-488 interface card provides the hardware (electrical and mechanical) and software required for you to interface your PC to the IEEE-488 bus. The software is packaged in read-only-memory (firmware) to provide versatile and easy-to-use IEEE-488 function extensions for your current programming language or operating system. Firmware cannot be accidentally erased or overwritten and it is always available for use by application programs. This manual provided a programming reference (Section 3.) and programming techniques (Section 4. and 5.) to assist you in writing your own application programs.
The key features of this interface card include (PCL-848A) :
Operating in one of the two modes (switch selectable).
Mode A : Compatible with PCL-748 and use the on-board firmware driver.
Mode N : Software compatible with National Instrument PC-II and IBM-PC GP-IB adaptor and use the driver and software developed for them.
- Implementation of the entire IEEE-488 PCL-848A
- Powerful and easy-to-use software command set. Fewer arguments and simple initialization.
- Software driver is in on-board firmware. Requires no additional disk operation when using BASIC or Turbo Pascal.
- On-board RAM for working space. No system memory space is needed for the IEEE-488 interface operation.
- Built-in 16 bit digital output port provides a convenient and economical solution for signal switching and digital control applications. The D/O port is compatible with the daughter boards: PCLD-785 Relay Output Board, PCLD-786 SSR & Relay Driver Board and PCL—789 Amplifier & Multiplexer Board.
- BASICA, BASIC compiler and Quick—BASIC are supported as
standard languages. C and Pascal language support packages
can he ordered separately as PCL-748—C and PCL—748-P. - The software can change the PC printer port to an IEEE-438
device. The PrtSc (print screen} key, all print statements,
word processing and spreadsheet programs that use printer
driver in BIOS can use IEEE—488 printers. - High speed direct memory access (DMA) with the ability to
handle 64K byte arrays.
-
-
PCL-849A – 4 Port RS-232 Interface Card
174,00 € Excl. VATAdd to cartFeatures PCL-849A:
• Four independent RS-232 serial ports
• Transmission speeds up to 921.6 Kbps (PCL-849)
• Independent I/O addresses, independent/shared IRQ settings
for each of 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, COM4
(PCL-849A/849B/849+)
• Supports surge protection: 3000 VDC (PCL-849B/849+)
• LED indicators on each port indicate data flow
• On-board interrupt status register for greater throughput
• Complete RS-232 modem-control signals
• Supports Windows 95/98/NT/ME/2000, Windows XP, Linux
(ICOM utility), DOS/Windows 3.1Introduction :
The PCL-849 series cards provide four individually configurable
RS-232 serial communication ports. The PCL-849A/849B/849L has a
16C554 UART which makes serial I/O more reliable. The higher
performance PCL-849+ has a 16C654 UART. By buffering data into
64-byte packets before putting it on the bus, UARTs drastically reduce
the CPU load. This makes the PCL-849+ especially suitable for high
speed serial I/O applications under multitasking environments.
The PCL-849 series cards support two operating modes, standard
mode and enhanced mode. In enhanced mode, the address for all four
ports can be set automatically. The PCL-849 series cards also support
either shared IRQ or independent IRQ functions. When an on-board
interrupt occurs, the interrupt status register (vector address) indicates
which port generated it. The shared interrupt can be set to most common
(extended) AT interrupts. This simplifies programming, speeds up
interrupt processing and frees up interrupts for other devices.Specifications PCL-849A :
• Ports: 4 serial ports
• I/O Address Range: from 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12, 15
• Data Bits: 5, 6, 7, 8
• Stop Bits: 1, 1.5, 2
• Parity: none, even, odd
• UARTs: 1 x 16C554 (PCL-849A/849B/849L)
1 x 16C654 (PCL-849+)
• Speed: 50 ~ 921.6 Kbps (PCL-849A)
50 ~ 460.8 Kbps (PCL-849B/849+)
50 ~ 115.2 Kbps (PCL-849L)
• Cables: 30-cm male DB-37 to four male DB-25 (DTE)
• Data Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
• Surge Protection: 3000 VDC (PCL-849B/849+)
2000 VDC (PCL-849L)
• Power Requirements: +5 V @ 250 mA typical, 500 mA max.
±12 V @ 70 mA typical, 120 mA max.
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″)
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage Temperature: -25 ~ 80° C (-13 ~ 176° F) -
PCL-860 – 4 1/2 DIGIT VOLTMETER (Rev A2)
350,00 € Excl. VATAdd to cartIntroduction
The PCL-860 is a 4 1/2 digit DC/AC voltmeter card that plugs into any I/O slot of IBM PC/XT/AT or compatible computers.It provides all the features and accuracy you would expect from a bench-top voltmeter.
It uses the computer screen as its display and it takes one forth of the screen when activated. This size allows 4 separate PC’s instruments (including the PCL-860) display on the screen at same time. In addition, instead of using push-buttons on the instrument front panel,it uses the computer keyboard.The PCL-860 provides a standard programmable DC current source.It can be used as a 4-wire resistance precision ohmmeter. The PCL-860 has also a build-in 16 bit digital output
1.2. Specifications PCL-860
Input impedance 10Mohm
DC voltage
Range Resblution Accuracy200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1Over voltage : 250V DC or peak AC
AC voltage : True RMS
Range Resblution Accuracy
200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1250V DC or peak AC
AC bandwidth :10KHz
Current source : 0.1mA, lmA, 10mA , user defined (< =1OmA)
* Resistance : (4 wire measurement with current source)
Range Resolution Accuracy Current Source20ohm 1 mili-ohm ±0.03% +1 10mA
200ohm 10 mili-ohm ±0.03%+ 1 10mA
2Kohm 0.1ohm ±0.03% +1 lmA
20Kohm lohm ±0.03%+1 0.1mA
* Conversion rate : 2.5, 5, 10 reading/sec
* Digital output : 16 channel TTL compatible 8.0mA sink and 0.4 mA driver
General :
* Power consumption : +5V, 390mA; +12V, 210mA typical* Digital output connecter: 20 pin flat cable connector with +5V, +12V, ground
* I/O base address : &H200-&H3F0 (factory setting is &H230)
* Operating temperature : 0 – 50°C
* Storage temperature : -20 – 65°C
* Weight : 290gm -
POC-154CB-AC-AE-
731,00 € – 796,00 € Excl. VATSelect optionsManufacturer’s warranty has expired
The POC-154 is a medical grade multimedia Panel Computer. This medical system is UL60601-1/EN60601-1 approved. Low-audible noise supplies an ideal and secure point-of-care solution for patients and hospital practitioners. The POC-154 is specially designed to resist spills and water damage, and ensures dust resistance with its protected LCD, sealed ports and card slots. It is equipped with a high brightness 350 cd/m2 LCD. The 400 : 1 contrast ratio makes the POC-154 a perfect image terminal for PACS & DICOM applications.
Specifications
General
§ Dimension (W x H x D) 414 x 339 x 115 mm (16.30” x 13.34” x 4.52”)
§ Weight 6.5 kg ( 14.4 lb )
§ Power supply AC model: 180 watts
Input voltage: 100~240 VAC, 4/2 A max. @ 50 ~ 60 Hz
Output voltages: +5 V @ 12 A, +12 V @ 12 A,
+3.3 V @ 16.8 A, +5 Vsb @ 2.0 A, -12 V @ 0.8 A DC model: 60 watts
Input voltage: +24 VDC, 7.5 A max
Output voltage: +5 V @ 10 A, +12 V @ 4 A,
-12 V @ 1 A, +3.3 V @ 8 A, +5 Vsb @ 0.75 A
§ Cooling fan Dimensions 60 x 60 x 10 mm (2.4″ x 2.4″ x 0.4″)
(L x W x H)
§ Front panel IP65/NEMA 4 compliant
Standard PC Function
§ CPU Intel® Pentium® 4 Mobile
§ Memory 2 x 184-pin DIMM socket accepts up to 2 GB DDR 266 DRAM (1GB installed)
§ HDD 1 x 2.5″ IDE HDD
§ FDD 1.44 MB
§ CD-ROM Compact CD-ROM (Optional: CD RW/DVD ROM COMBO)
§ PCMCIA 2 x Type II
§ I/O Ports & Speakers 4 x Serial ports: 3 x RS232 x 3, 1 x RS-232/422/485;
1 x Parallel port; 2 x USB ports
1 x PS/2 mouse and K/B;
1 x MIC-in, Line-in, Speaker-out,
2 x 1 W speakers
§ Network (LAN) 2 x 10/100Base-T Ethernet interface
§ Bus Expansion 1 x PCI 2.2 expansion slot
§ Optional 802.11b wireless antenna with wireless LAN PCMCIA module
General Specifications of Display
§ Display type 15″ TFT LCD
§ Resolution 1024 x 768
§ Colors 262,144 (6 bits/color)
§ Dot size (mm) 0.264 x 0.264
§ Viewing angle 120°
§ Luminance 350 cd/m2
§ Contrast ratio 400 : 1
§ LCD MTBF 50,000 hours
§ Backlight lifetime 50,000 hours at 6.5 mA
Environmental Specifications
§ Temperature 0 ~ 40 °C
§ Relative Humidity 10 ~ 95% @ 40 °C (non-condensing)
§ Shock 30 G peak acceleration (11 msec duration)
§ Power MTBF 100,000 hrs
§ Certification CE, FCC, VCCI, BSMI approved
§ AC Model UL60950, UL60601-1, EN60950, EN60601-1 approved
Mounting
- VESA 75×75 mm, 100×100 mm
-
POC-154CB-AC-AE- 40GB HDD
817,00 € Excl. VATAdd to cartManufacturer’s warranty has expired
The POC-154 is a medical grade multimedia Panel Computer. This medical system is UL60601-1/EN60601-1 approved. Low-audible noise supplies an ideal and secure point-of-care solution for patients and hospital practitioners. The POC-154 is specially designed to resist spills and water damage, and ensures dust resistance with its protected LCD, sealed ports and card slots. It is equipped with a high brightness 350 cd/m2 LCD. The 400 : 1 contrast ratio makes the POC-154 a perfect image terminal for PACS & DICOM applications.
Specifications
General
§ Dimension (W x H x D) 414 x 339 x 115 mm (16.30” x 13.34” x 4.52”)
§ Weight 6.5 kg ( 14.4 lb )
§ Power supply AC model: 180 watts
Input voltage: 100~240 VAC, 4/2 A max. @ 50 ~ 60 Hz
Output voltages: +5 V @ 12 A, +12 V @ 12 A,
+3.3 V @ 16.8 A, +5 Vsb @ 2.0 A, -12 V @ 0.8 A DC model: 60 watts
Input voltage: +24 VDC, 7.5 A max
Output voltage: +5 V @ 10 A, +12 V @ 4 A,
-12 V @ 1 A, +3.3 V @ 8 A, +5 Vsb @ 0.75 A
§ Cooling fan Dimensions 60 x 60 x 10 mm (2.4″ x 2.4″ x 0.4″)
(L x W x H)
§ Front panel IP65/NEMA 4 compliant
Standard PC Function
§ CPU Intel® Pentium® 4 Mobile 2.2GHz
§ Memory 2 x 184-pin DIMM socket accepts up to 2 GB DDR 266 DRAM (1GB installed)
§ HDD 1 x 2.5″ IDE HDD 40GB
§ FDD 1.44 MB
§ CD-ROM Compact CD-ROM (Optional: CD RW/DVD ROM COMBO)
§ PCMCIA 2 x Type II
§ I/O Ports & Speakers 4 x Serial ports: 3 x RS232 x 3, 1 x RS-232/422/485;
1 x Parallel port; 2 x USB ports
1 x PS/2 mouse and K/B;
1 x MIC-in, Line-in, Speaker-out,
2 x 1 W speakers
§ Network (LAN) 2 x 10/100Base-T Ethernet interface
§ Bus Expansion 1 x PCI 2.2 expansion slot
§ Optional 802.11b wireless antenna with wireless LAN PCMCIA module
General Specifications of Display
§ Display type 15″ TFT LCD
§ Resolution 1024 x 768
§ Colors 262,144 (6 bits/color)
§ Dot size (mm) 0.264 x 0.264
§ Viewing angle 120°
§ Luminance 350 cd/m2
§ Contrast ratio 400 : 1
§ LCD MTBF 50,000 hours
§ Backlight lifetime 50,000 hours at 6.5 mA
Environmental Specifications
§ Temperature 0 ~ 40 °C
§ Relative Humidity 10 ~ 95% @ 40 °C (non-condensing)
§ Shock 30 G peak acceleration (11 msec duration)
§ Power MTBF 100,000 hrs
§ Certification CE, FCC, VCCI, BSMI approved
§ AC Model UL60950, UL60601-1, EN60950, EN60601-1 approved
Mounting
- VESA 75×75 mm, 100×100 mm
-
POC-155CD-AC-AE
795,50 € Excl. VATAdd to cartManufacturer’s warranty has expired
The POC-155 is a medical multimedia Panel Computer that is UL60601-1/EN60601-1 approved. The low-current-leakage power supply of POC-155 makes it an ideal and safe point-of-care solution for patients and hospital practitioners. The POC-155 is specially designed to resist spills and water damage, and ensures dust resistance with its protected LCD, sealed ports and card slots. The high brightness (350 cd/m2) and good contrast ratio (400:1) of the POC-155 LCD makes it a perfect image terminal for PACS and DICOM applications. -
POC-155CD-AC-AE-resT/S
968,00 € Excl. VATAdd to cartManufacturer’s warranty has expired
The POC-155 is a medical multimedia Panel Computer that is UL60601-1/EN60601-1 approved. The low-current-leakage power supply of POC-155 makes it an ideal and safe point-of-care solution for patients and hospital practitioners. The POC-155 is specially designed to resist spills and water damage, and ensures dust resistance with its protected LCD, sealed ports and card slots. The high brightness (350 cd/m2) and good contrast ratio (400:1) of the POC-155 LCD makes it a perfect image terminal for PACS and DICOM applications. -
POC-174CB-AC- A Point-of-Care Terminal
860,00 € – 882,00 € Excl. VATSelect optionsThe POC-174 is a medical-grade Point-of Care Panel PC with a 17” display optimized for minimal power leakage and low EMI. It is approved according to EN60601-1 and UL2601-1 standards. This certifies that there is no interference with medical equipment that can pose a health risk for patients. The POC-174 has also been also approved with IP65/NEMA 4 and IPX1 for dust-resistance and water spills. Like the other products in the POC series, the POC-174 has all the characteristics needed for use in critical medical environments. Its high brightness, resolution, and contrast ratio LCD display is especially suitable for medical diagnosis and treatment methods like: CT diagnosis, electrical X-ray, PACS and DICOM. With a wide range of I/O options, the POC series supply full connectivity, and offer the most secure and practical healthcare terminals for patients and practitioners.
Manufacturer’s warranty has expired.
Specifications POC-174CB-AC-
General
§ Dimension (W x H x D) 437 x 377 x 131 mm (17.20″ x 14.84″ x 5.15″)
§ Weight 12 kg (26.5 lb)
§ Power Supply AC model: 180 watt
Input voltage: 100 ~ 240 VAC, 4 A max.@ 50 ~ 60 Hz
Output voltages: +5 V @ 12 A, +12 V @ 12 A
+3.3 V @ 16.8 A, +5 Vsb @ 2.0 A, -12 V @ 0.8 A DC model:
Input voltage: +24 VDC, 7.5 A max
Output voltage: +5 V @ 10 A, +12 V @ 4 A,
-12 V @ 1 A, +3.3 V @ 8 A, +5 Vsb @ 0.75 A
§ Cooling Fan (L x W x H) 60 x 60 x 10 mm (2.4″ x 2.4″ x 2.4″)
§ Front Panel IP65/NEMA compliant
Standard PC Functions
§ CPU Intel® Pentium® 4 Mobile
§ Memory 2 x 184-pin DIMM socket accepts up to 2 GB DDR333/266 DRAM 1GB installed)
§ HDD 1 x 2.5″ IDE HDD
§ FDD 1.44 MB
§ CD ROM Slim type (Optional: CD-RW/DVD-ROM)
§ PCMCIA 2x Type II
§ I/O Ports &Speakers 4 x Serial ports: 3 x RS-232, 1 x RS-232/422/485;
1 x Parallel port
2 x USB ports
1 x PS/2 mouse and keyboard interface
1x Mic-in
1 x Line-in
1 x Speaker-out
2 x 1 W speakers
§ Network (LAN) 2 x 10/100Base-T Ethernet interface
§ Bus Expansion 1 x PCI 2.2 expansion slot
§ Optional 802.11b wireless antenna with wireless LAN PCMCIA module
Display Specifications
§ Display Type 17″ TFT LCD
§ Max.Resolution 1280 x 1024
§ Colors 16.7 M (8 bits/color)
§ Dot Size (mm) 0.264 x 0.264
§ Viewing Angle 170°
§ Luminance 250 cd/m2
§ Contrast Ratio 600 : 1
§ LCD MTBF 50,000 hours
§ Backlight Lifetime 40,000 hours
Specifications Cont.
Environmental Specifications
§ Temperature 0 ~ 40° C
§ Relative Humidity 10 ~ 95% @ 40° C (non-condensing)
§ Shock 50 G peak acceleration (11 msec duration)
§ Power MTBF 100,000 hrs
§ Certifications CE, FCC, VCCI, BSMI approved
§ AC Model UL60950, UL60601-1, EN60950, EN60601-1 approved
§ DC Model FCC, UL60601-1, EN60601-1 approved
Mounting
- Vesa 75 x 75 mm, 100 x 100 mm
-
POC-195 CD-AC – Point-of-Care Terminal
989,00 € Excl. VATAdd to cartFeatures POC-195 CD-AC : √19″ high quality LCD display with 16.7M colors and 1300:1 contrast ratio POC-195 √User-Friendly design with front function keys √Isolated design provides unique electric leakage protection for COM ports and LAN ports √IPX1 water resistant enclosure with additional IP65 dust-tight front panel √UL60601-1/EN60601-1, CE & FCC Class B certified √Optional 802.11b/g …
