Category: Serial Communication Cards
Serial Communication Cards
Showing all 12 results
-
PCI-1625 – 8-Port Intelligent RS-232 Card
365,00 € Excl. VATAdd to cartFEATURES PCI-1625:
√RISC processor (TMS320)
√1 MB SRAM
√PCI Specification 2.2 compliant
√Speed up to 921.6 kbps
√8-port RS-232
√I/O address automatically assigned by PCI Plug &Play
√OS supported: Windows 2000/XP
√Powerful and easy to use utility (ICOM tools)
√Link with OPT8FP peripherals up to 1200m (4000ft) from controller (RS-422)
√Universal PCI (Supports 3.3 V or 5 V PCI bus signal) -
-
PCL-721 – 32 Channel D/I Card
156,00 € Excl. VATAdd to cartIntroduction PCL-721 :
The PCL-721/723 is a 32/24-channel digital input card with independent
interrupt capabilities that allows the PCL-721/723 to work in the
background while the processor perform other jobs in the foreground. With
this feature, your system can do real-time Process monitoring without
polling its inputs, channel by channel.The PCL-721/723 has two modes: normal and interrupt. While it is set to
normal mode, the PCL-721/723 serves as a general purpose multi-channel
digital input card. However,if it is set to interrupt mode, then each channel
will generate an interrupt request to the PC, once the channel input has
changed.The 32digital input channels ofthe PCL-721 are divided into 4 groups. The
24 digital input channels of the PCL-723 are divided into 3 groups. Each
group handles8 digital input channels. There is a register that reflects the
interrupt status of each groups. Users can first read this register to check
which group caused the interrupt, then by reading the 8channels’ status of
that group, you can easily find which channel generated the interrupt. This
two-pass feature saves lot of time to determine which service routine should
be executed in your ISR (Interrupt Service Routine).The PCL-721/723 is easy to configure. No switch or jumper settings are
needed (except the I/O base address). The IRQ level, individual channel’s
trigger mode (rising or falling edge), and interrupt mask (enable or disable)
are all software programmable -
PCL-731 – 48bit Digital I/O Card
131,00 € Excl. VATAdd to cartFeatures:
• 48 digital I/O lines
• Emulates 8255 PPI mode 0
• Buffered circuits for higher driving capacity than the 8255
• Interrupt handling
• Output status readback
• Pin compatible with Opto-22 I/O module racksIntroduction :
The PCL-731 offers 48 programmable digital I/O lines. Each port
emulates the operation of an 8255 Programmable Peripheral
Interface (PPI) chip in mode 0, but provides a higher driving capacity
than the 8255.
The card’s DIO ports are combined into 8-bit ports, six for the
PCL-731. You can configure each port individually by software for
either input or output. The card can directly interface with SSR
module carrier boards through a 50-pin Opto-22 compatible
connector.
The PCL-731 is a low-cost alternative of the PCL-722. Like the
PCL-722 it provides a readback feature which lets you monitor the
status of the output by reading back the output portApplications
• Digital I/O control
• Industrial monitoring and control
• Interfacing with parallel I/O devices
• Interfacing with Opto-22 compatible I/O module racks
Specifications
• I/O lines: 48
• Programming mode: 8255 PPI mode 0
• Interrupt: Bit 0 of one port can generate an interrupt to
IRQ 2~15
• Interrupt triggering: Rising or falling edge triggering, jumperselectable
• Digital output: Logic 0: 0.4 V max. @ 24 mA (sink)
Logic 1: 2.4 V min. @ 15 mA (source)
• Digital input: Logic 0: 0.4 V max.
Logic 1: 2.4v minGeneral PCL-731
• Power consumption:+5 V @ 0.5 A typical
+5 V @ 0.8 A max.
• Operating temperature: 0 ~ +60° C (32 ~ 140° F)
• Storage temperature: -20 ~ +70° C (-4 ~ 158° F)
• Operating humidity: 5 ~ 95% RH non-condensing (refer to IEC
68-2-3)
• Connectors: 2×50-pin male ribbon-cable connectors
• Dimensions: 185 mm (L) x 100 mm (H) (7.3″ x 3.9″)Ordering Information
PCL-731: 48-bit digital I/O card and manual
PCL-10150-1.2: 50-pin flat cable, 1.2 m
PCLD-782B: 24/16-ch. opto-isolated digital input board
PCLD-785B: 24/16-ch. relay output board
PCLD-7216: 16-ch. carrier board for SSR I/O modules
PCLD-885: 16-ch. power relay (Form A) output board
PCLS-OCX: ActiveX Control for data acquisition and control.
ADAM-3950: 50-pin flat cable wiring terminal for DIN-rail -
PCL-733 – 32Ch.Isolated DI Card W.Inter.
212,00 € Excl. VATAdd to cartFeatures PCL-733 :
√ 32 isolated, digital input channels PCL-733
√ High-voltage isolation (2,500 VDC)
√ Interrupt capacity
√ D-type connectors for isolated input channels
√ Reverse voltage protection for isolated input channels (up to 24 VDCSpecifications PCL-733 :
Isolated Digital Input
√ Input Channels 32 (16-ch/group)
√ Input Voltage Logic 0: PCI-1733: 2 V max., PCL-733: 1 V max.
Logic 1: 5 V min.
PCI-1733: 30 V max., PCL-733: 24 V max.√Interrupt Capable Ch. 4 for PCI-1733, 2 for PCL-733
√ Isolation Protection 2,500 VDC
√ Opto-Isolator Response PCL-733: 100 µs, PCI-1733: 25 µs
√ Input Resistance PCI-1733: 2.7 kΩ @ 1 W
: 1.2 kΩ @ 0.5 W
General
√ Bus Type PCI-1733: PCI V2.2, : ISA
√ I/O Connectors 1 x 37-pin D-type female
√ Dimensions (L x H) : 185 x 100 mm (7.3” x 3.9”)
: 175 x 100 mm (6.9” x 3.9”)
√ Power Consumption
: Typical: +5 V @ 320 mA
Max: +5 V @ 500 mA
PCI-1733: Typical: 5V @ 200 mA, 12 V @ 50 mA
Max: 5V @ 350 mA, 12 V @ 75 mA
√ Operating Temperature 0 ~ 60° C (32 ~ 140° F)
√ Storing Temperature PCL-733: -20 ~ 70° C (-4 ~ 158° F)
PCI-1733: -25 ~ 85° C (-13 ~ 185° F)
√ Storing Humidity 5 ~ 95% RH, non-condensing (IEC 68-2-3)Ordering Information
√ PCI-1733 32-channel isolated PCI digital input card, manual and
driv er CD-ROM (cable not included)
√ 32-channel isolated digital input card, manual and
driver CD-ROM (cable not included)
√ PCLD-780 Universal screw terminal board
√ PCLD-880 Universal screw terminal board
√ ADAM-3937 DB37 wiring terminal for DIN-rail mounting
√ PCL-10137-1 DB37 cable, 1m
√ PCL-10137-2 DB37 cable, 2m
√ PCL-10137-3 DB37 cable, -
PCL-752 – Intelligent SYSTEM MONITORCard
383,00 € Excl. VATAdd to cartFeatures PCL-752
• Monitoring +5VDC,-5VDC, +12VDC., -12VDC of ISA bus voltage
• Three external voltage sense inputs
• Three fan sense inputs for fan speed monitoring
• Three temperature sense inputs
• Two “power good” signal inputs for power supply monitoring
• Two isolated digital inputs
• Three relay outputs for alarm connection
• Watchdog timer for detecting system CPU operation
• One serial port can be set as a RS-232 or RS-485 port, supporting
modem output for connection to remote system center
• Three configurable alarm levels: Critical, major, minor
• Audible alarm with three sound effects
• On-board battery backup ensuring normal card operation in case of
• system power failure
• Built-in watchdog timer for self-detection ensuring reliable card
operation
• Compact half-sized card dimensions -
PCL-839 – HIGH SPEED STEP MOTOR CONTROL.
576,00 € Excl. VATAdd to cartIntroduction
PCL-839 is a high-speed three-axis stepping motor control card that
simplifies stepping motor control, giving you added performance from
your stepping motors.Three-axis control
The PCL-839 has three single-chip pulse generators on-board, which
enables the simultaneous and independent control of three axis. The
PCL-839 provides digital pulse and directional control (+ and -) for each
stepping motor axis.User-friendly interface
The PCL-839 has been designed to act as a user-friendly solution for
your stepping motor control applications. Programming the PCL-839 is
very easy. ‘C’ Libraries are provided and they contain all the command
functions needed for total control of your stepping motors.Stand-alone interpreter
A stand-alone, non-resident command interpreter, PROGg39.EXE, can
also be used to control your stepping motors without any programming.
Digital I/O
The PCL-839 features 16 digital inputs and 16 digital outputs for general
I/O use (on/off control etc.).
Isolation protection
The PCL-839’s PULSE and DIRECTION outputs and five limits input
switches are isolated from the PC side.Features of PCL-839 :
· Three on-board pulse generators that enables simultaneous independent
control of three stepping motors
· Two operating modes – two-pulse (+ and – direction pulse) or one-pulse
(pulse-direction) mode
· Programmable step rate from 1 to 16k pps (pulses per second).
· Programmable initial speed, final speed and time duration. Automatic
trapezoidal acceleration/deceleration Tamping is performed
· 16 I/O TTL compatible channels
· All inputs/outputs are optically isolated, providing 500VDC isolation
protection
· ‘C’ libraries containing device drivers provided
· Command Interpreter provided that eases learning the PCL-839 command
setApplications
· Precise X-Y-Z position control
· Precise rotation control
· Robotics and assembly equipment
· Other stepping-motor applicationsGeneral
· Power consumption: 300mA, +5VDC
· Connector: 37-pin D-type connector
· Board dimensions: 183.5 mm x 99.06 mm
· Operatingtemperature:0 to70°C -
PCL-847A – 4 Port RS-422/485 Card
180,00 € Excl. VATAdd to cartFeatures PCL-847A :
• Four independent RS-422/485 serial ports
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS control PCL-847AIntroduction:
PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires.Specifications PCL-847A :
• Ports: 4
• UART: 4 x 16C550 with 16-byte FIFO
• Speed: 50 ~ 921.6 Kbps
• Parity: none, even, odd
• Signal support:
TxD+, TxD-, RxD+, RxD-, CTS+, CTS-, RTS+ and RTS-
• I/O address: From 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Isolation voltage: 1000 VDC (PCL-846A/846B only)
• Surge protection: 3000 VDC (PCL-846B/847B)
• Power consumption: +5 V @ 250 mA typical, 500 mA max.
• Cables: 30-cm male DB-37 to four male DB-9 (DTE)
• Operating temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage temperature: -25 ~ 80° C (-13 ~ 176° F)
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″) -
PCL-847B – 4 Port RS-422/485 Card SurgeP
230,00 € Excl. VATAdd to cartFeatures PCL-847B:
• Four independent RS-422/485 serial ports PCL-847B
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS controlIntroduction PCL-847B:
PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.
An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires. -
PCL-848A – IEEE-488 CONTROLLER
277,00 € Excl. VATAdd to cart-
General Information PCL-848A
- Introduction to the Product PCL-848A
The PCL-848A/B IPSE-488 interface card is a valuable addition to your PC that allows you to communicate with over 2000 products, made by over 200 manufacturers, in over 14 countries. The IEEE- 488-1978 standard that this IEEE-488 card implements is the most widely used international standard for information transfer between computer and electronic instruments. There are numerous publications and articles that may be used in conjunction with this manual to assist you to understand the interface standard. The IEEE reference document may be ordered by writing to the IEEE Service Center, 445 Hoes Lane, Piscataway, NJ 08854, USA.
The IEEE-488 interface card provides the hardware (electrical and mechanical) and software required for you to interface your PC to the IEEE-488 bus. The software is packaged in read-only-memory (firmware) to provide versatile and easy-to-use IEEE-488 function extensions for your current programming language or operating system. Firmware cannot be accidentally erased or overwritten and it is always available for use by application programs. This manual provided a programming reference (Section 3.) and programming techniques (Section 4. and 5.) to assist you in writing your own application programs.
The key features of this interface card include (PCL-848A) :
Operating in one of the two modes (switch selectable).
Mode A : Compatible with PCL-748 and use the on-board firmware driver.
Mode N : Software compatible with National Instrument PC-II and IBM-PC GP-IB adaptor and use the driver and software developed for them.
- Implementation of the entire IEEE-488 PCL-848A
- Powerful and easy-to-use software command set. Fewer arguments and simple initialization.
- Software driver is in on-board firmware. Requires no additional disk operation when using BASIC or Turbo Pascal.
- On-board RAM for working space. No system memory space is needed for the IEEE-488 interface operation.
- Built-in 16 bit digital output port provides a convenient and economical solution for signal switching and digital control applications. The D/O port is compatible with the daughter boards: PCLD-785 Relay Output Board, PCLD-786 SSR & Relay Driver Board and PCL—789 Amplifier & Multiplexer Board.
- BASICA, BASIC compiler and Quick—BASIC are supported as
standard languages. C and Pascal language support packages
can he ordered separately as PCL-748—C and PCL—748-P. - The software can change the PC printer port to an IEEE-438
device. The PrtSc (print screen} key, all print statements,
word processing and spreadsheet programs that use printer
driver in BIOS can use IEEE—488 printers. - High speed direct memory access (DMA) with the ability to
handle 64K byte arrays.
-
-
PCL-849A – 4 Port RS-232 Interface Card
174,00 € Excl. VATAdd to cartFeatures PCL-849A:
• Four independent RS-232 serial ports
• Transmission speeds up to 921.6 Kbps (PCL-849)
• Independent I/O addresses, independent/shared IRQ settings
for each of 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, COM4
(PCL-849A/849B/849+)
• Supports surge protection: 3000 VDC (PCL-849B/849+)
• LED indicators on each port indicate data flow
• On-board interrupt status register for greater throughput
• Complete RS-232 modem-control signals
• Supports Windows 95/98/NT/ME/2000, Windows XP, Linux
(ICOM utility), DOS/Windows 3.1Introduction :
The PCL-849 series cards provide four individually configurable
RS-232 serial communication ports. The PCL-849A/849B/849L has a
16C554 UART which makes serial I/O more reliable. The higher
performance PCL-849+ has a 16C654 UART. By buffering data into
64-byte packets before putting it on the bus, UARTs drastically reduce
the CPU load. This makes the PCL-849+ especially suitable for high
speed serial I/O applications under multitasking environments.
The PCL-849 series cards support two operating modes, standard
mode and enhanced mode. In enhanced mode, the address for all four
ports can be set automatically. The PCL-849 series cards also support
either shared IRQ or independent IRQ functions. When an on-board
interrupt occurs, the interrupt status register (vector address) indicates
which port generated it. The shared interrupt can be set to most common
(extended) AT interrupts. This simplifies programming, speeds up
interrupt processing and frees up interrupts for other devices.Specifications PCL-849A :
• Ports: 4 serial ports
• I/O Address Range: from 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12, 15
• Data Bits: 5, 6, 7, 8
• Stop Bits: 1, 1.5, 2
• Parity: none, even, odd
• UARTs: 1 x 16C554 (PCL-849A/849B/849L)
1 x 16C654 (PCL-849+)
• Speed: 50 ~ 921.6 Kbps (PCL-849A)
50 ~ 460.8 Kbps (PCL-849B/849+)
50 ~ 115.2 Kbps (PCL-849L)
• Cables: 30-cm male DB-37 to four male DB-25 (DTE)
• Data Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
• Surge Protection: 3000 VDC (PCL-849B/849+)
2000 VDC (PCL-849L)
• Power Requirements: +5 V @ 250 mA typical, 500 mA max.
±12 V @ 70 mA typical, 120 mA max.
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″)
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage Temperature: -25 ~ 80° C (-13 ~ 176° F) -
PCL-860 – 4 1/2 DIGIT VOLTMETER (Rev A2)
350,00 € Excl. VATAdd to cartIntroduction
The PCL-860 is a 4 1/2 digit DC/AC voltmeter card that plugs into any I/O slot of IBM PC/XT/AT or compatible computers.It provides all the features and accuracy you would expect from a bench-top voltmeter.
It uses the computer screen as its display and it takes one forth of the screen when activated. This size allows 4 separate PC’s instruments (including the PCL-860) display on the screen at same time. In addition, instead of using push-buttons on the instrument front panel,it uses the computer keyboard.The PCL-860 provides a standard programmable DC current source.It can be used as a 4-wire resistance precision ohmmeter. The PCL-860 has also a build-in 16 bit digital output
1.2. Specifications PCL-860
Input impedance 10Mohm
DC voltage
Range Resblution Accuracy200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1Over voltage : 250V DC or peak AC
AC voltage : True RMS
Range Resblution Accuracy
200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1250V DC or peak AC
AC bandwidth :10KHz
Current source : 0.1mA, lmA, 10mA , user defined (< =1OmA)
* Resistance : (4 wire measurement with current source)
Range Resolution Accuracy Current Source20ohm 1 mili-ohm ±0.03% +1 10mA
200ohm 10 mili-ohm ±0.03%+ 1 10mA
2Kohm 0.1ohm ±0.03% +1 lmA
20Kohm lohm ±0.03%+1 0.1mA
* Conversion rate : 2.5, 5, 10 reading/sec
* Digital output : 16 channel TTL compatible 8.0mA sink and 0.4 mA driver
General :
* Power consumption : +5V, 390mA; +12V, 210mA typical* Digital output connecter: 20 pin flat cable connector with +5V, +12V, ground
* I/O base address : &H200-&H3F0 (factory setting is &H230)
* Operating temperature : 0 – 50°C
* Storage temperature : -20 – 65°C
* Weight : 290gm
