PCL-839 – HIGH SPEED STEP MOTOR CONTROL.

576,00 € Excl. VAT

Introduction

PCL-839 is a high-speed three-axis stepping motor control card that
simplifies stepping motor control, giving you added performance from
your stepping motors.

Three-axis control
The PCL-839 has three single-chip pulse generators on-board, which
enables the simultaneous and independent control of three axis. The
PCL-839 provides digital pulse and directional control (+ and -) for each
stepping motor axis.

User-friendly interface
The PCL-839 has been designed to act as a user-friendly solution for
your stepping motor control applications. Programming the PCL-839 is
very easy. ‘C’ Libraries are provided and they contain all the command
functions needed for total control of your stepping motors.

Stand-alone interpreter
A stand-alone, non-resident command interpreter, PROGg39.EXE, can
also be used to control your stepping motors without any programming.
Digital I/O
The PCL-839 features 16 digital inputs and 16 digital outputs for general
I/O use (on/off control etc.).
Isolation protection
The PCL-839’s PULSE and DIRECTION outputs and five limits input
switches are isolated from the PC side.

Features of PCL-839 :

· Three on-board pulse generators that enables simultaneous independent
control of three stepping motors
· Two operating modes – two-pulse (+ and – direction pulse) or one-pulse
(pulse-direction) mode
· Programmable step rate from 1 to 16k pps (pulses per second).
· Programmable initial speed, final speed and time duration. Automatic
trapezoidal acceleration/deceleration Tamping is performed
· 16 I/O TTL compatible channels
· All inputs/outputs are optically isolated, providing 500VDC isolation
protection
· ‘C’ libraries containing device drivers provided
· Command Interpreter provided that eases learning the PCL-839 command
set

Applications

· Precise X-Y-Z position control
· Precise rotation control
· Robotics and assembly equipment
· Other stepping-motor applications

General
· Power consumption: 300mA, +5VDC
· Connector: 37-pin D-type connector
· Board dimensions: 183.5 mm x 99.06 mm
· Operatingtemperature:0 to70°C

Add to cart

PCL-844 – 8 Port Intelligent RS-232 Card

316,00 € Excl. VAT

RISC Processor (TMS 320) 512 KB dual-port RAM Transmission speed up to 921.6 kbps with eight ports on-line Complete RS-232 modem control signals Maps to just 16 KB of system memory. Choose one of six addresses from C8000 to DC000. Many IRQ options: 2, 3, 4, 5, 7, 10, 11, 12 or 15 Easy-to-use menu …

PCL-844 – 8 Port Intelligent RS-232 CardRead More

Add to cart

PCL-846A – 4 Port RS-422/485 Card Isolat.

274,00 € Excl. VAT

Features PCL-846A: √Four or eight RS-232 or RS-422/485 serial ports PCL-846A √Transmission speeds up to 921.6 kbps √Independent/shared IRQ settings between each of the 4 serial ports √Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15 √Supports COM1, COM2, COM3, and COM4 √Provides 1000 VDC isolation (PCL-846 only) √Provides …

PCL-846A – 4 Port RS-422/485 Card Isolat.Read More

Add to cart

PCL-847A – 4 Port RS-422/485 Card

180,00 € Excl. VAT

Features PCL-847A :

• Four independent RS-422/485 serial ports
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS control PCL-847A

Introduction:

PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.

An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires.

Specifications PCL-847A :

• Ports: 4
• UART: 4 x 16C550 with 16-byte FIFO
• Speed: 50 ~ 921.6 Kbps
• Parity: none, even, odd
• Signal support:
TxD+, TxD-, RxD+, RxD-, CTS+, CTS-, RTS+ and RTS-
• I/O address: From 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Isolation voltage: 1000 VDC (PCL-846A/846B only)
• Surge protection: 3000 VDC (PCL-846B/847B)
• Power consumption: +5 V @ 250 mA typical, 500 mA max.
• Cables: 30-cm male DB-37 to four male DB-9 (DTE)
• Operating temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage temperature: -25 ~ 80° C (-13 ~ 176° F)
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″)

Add to cart

PCL-847B – 4 Port RS-422/485 Card SurgeP

230,00 € Excl. VAT

Features PCL-847B:

• Four independent RS-422/485 serial ports PCL-847B
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS control

Introduction PCL-847B:

PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.
An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires.

Add to cart

PCL-848A – IEEE-488 CONTROLLER

277,00 € Excl. VAT

General Information PCL-848A
Introduction to the Product PCL-848A

The PCL-848A/B IPSE-488 interface card is a valuable addition to your PC that allows you to communicate with over 2000 products, made by over 200 manufacturers, in over 14 countries. The IEEE- 488-1978 standard that this IEEE-488 card implements is the most widely used international standard for information transfer between computer and electronic instruments. There are numerous publications and articles that may be used in conjunction with this manual to assist you to understand the interface standard. The IEEE reference document may be ordered by writing to the IEEE Service Center, 445 Hoes Lane, Piscataway, NJ 08854, USA.

The IEEE-488 interface card provides the hardware (electrical and mechanical) and software required for you to interface your PC to the IEEE-488 bus. The software is packaged in read-only-memory (firmware) to provide versatile and easy-to-use IEEE-488 function extensions for your current programming language or operating system. Firmware cannot be accidentally erased or overwritten and it is always available for use by application programs. This manual provided a programming reference (Section 3.) and programming techniques (Section 4. and 5.) to assist you in writing your own application programs.

The key features of this interface card include (PCL-848A) :

Operating in one of the two modes (switch selectable).

Mode A : Compatible with PCL-748 and use the on-board firmware driver.

Mode N : Software compatible with National Instrument PC-II and IBM-PC GP-IB adaptor and use the driver and software developed for them.

Implementation of the entire IEEE-488 PCL-848A
Powerful and easy-to-use software command set. Fewer arguments and simple initialization.
Software driver is in on-board firmware. Requires no additional disk operation when using BASIC or Turbo Pascal.
On-board RAM for working space. No system memory space is needed for the IEEE-488 interface operation.
Built-in 16 bit digital output port provides a convenient and economical solution for signal switching and digital control applications. The D/O port is compatible with the daughter boards: PCLD-785 Relay Output Board, PCLD-786 SSR & Relay Driver Board and PCL—789 Amplifier & Multiplexer Board.
BASICA, BASIC compiler and Quick—BASIC are supported as
standard languages. C and Pascal language support packages
can he ordered separately as PCL-748—C and PCL—748-P.
The software can change the PC printer port to an IEEE-438
device. The PrtSc (print screen} key, all print statements,
word processing and spreadsheet programs that use printer
driver in BIOS can use IEEE—488 printers.
High speed direct memory access (DMA) with the ability to
handle 64K byte arrays.

Add to cart

PCL-849A – 4 Port RS-232 Interface Card

174,00 € Excl. VAT

Features PCL-849A:

• Four independent RS-232 serial ports
• Transmission speeds up to 921.6 Kbps (PCL-849)
• Independent I/O addresses, independent/shared IRQ settings
for each of 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, COM4
(PCL-849A/849B/849+)
• Supports surge protection: 3000 VDC (PCL-849B/849+)
• LED indicators on each port indicate data flow
• On-board interrupt status register for greater throughput
• Complete RS-232 modem-control signals
• Supports Windows 95/98/NT/ME/2000, Windows XP, Linux
(ICOM utility), DOS/Windows 3.1

Introduction :
The PCL-849 series cards provide four individually configurable
RS-232 serial communication ports. The PCL-849A/849B/849L has a
16C554 UART which makes serial I/O more reliable. The higher
performance PCL-849+ has a 16C654 UART. By buffering data into
64-byte packets before putting it on the bus, UARTs drastically reduce
the CPU load. This makes the PCL-849+ especially suitable for high
speed serial I/O applications under multitasking environments.
The PCL-849 series cards support two operating modes, standard
mode and enhanced mode. In enhanced mode, the address for all four
ports can be set automatically. The PCL-849 series cards also support
either shared IRQ or independent IRQ functions. When an on-board
interrupt occurs, the interrupt status register (vector address) indicates
which port generated it. The shared interrupt can be set to most common
(extended) AT interrupts. This simplifies programming, speeds up
interrupt processing and frees up interrupts for other devices.

Specifications PCL-849A :

• Ports: 4 serial ports
• I/O Address Range: from 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12, 15
• Data Bits: 5, 6, 7, 8
• Stop Bits: 1, 1.5, 2
• Parity: none, even, odd
• UARTs: 1 x 16C554 (PCL-849A/849B/849L)
1 x 16C654 (PCL-849+)
• Speed: 50 ~ 921.6 Kbps (PCL-849A)
50 ~ 460.8 Kbps (PCL-849B/849+)
50 ~ 115.2 Kbps (PCL-849L)
• Cables: 30-cm male DB-37 to four male DB-25 (DTE)
• Data Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
• Surge Protection: 3000 VDC (PCL-849B/849+)
2000 VDC (PCL-849L)
• Power Requirements: +5 V @ 250 mA typical, 500 mA max.
±12 V @ 70 mA typical, 120 mA max.
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″)
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage Temperature: -25 ~ 80° C (-13 ~ 176° F)

Add to cart

PCL-860 – 4 1/2 DIGIT VOLTMETER (Rev A2)

350,00 € Excl. VAT

Introduction

The PCL-860 is a 4 1/2 digit DC/AC voltmeter card that plugs into any I/O slot of IBM PC/XT/AT or compatible computers.It provides all the features and accuracy you would expect from a bench-top voltmeter.
It uses the computer screen as its display and it takes one forth of the screen when activated. This size allows 4 separate PC’s instruments (including the PCL-860) display on the screen at same time. In addition, instead of using push-buttons on the instrument front panel,it uses the computer keyboard.

The PCL-860 provides a standard programmable DC current source.It can be used as a 4-wire resistance precision ohmmeter. The PCL-860 has also a build-in 16 bit digital output

1.2. Specifications PCL-860

Input impedance 10Mohm

DC voltage
Range Resblution Accuracy

200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1

Over voltage : 250V DC or peak AC

AC voltage : True RMS

Range Resblution Accuracy

200mv 10uv ±0.03%+1
2V 100uV ±0.03%+1
20V lmV ±0.03%+1
200V 10mV ±0.03%+1

250V DC or peak AC

AC bandwidth :10KHz

Current source : 0.1mA, lmA, 10mA , user defined (< =1OmA)

* Resistance : (4 wire measurement with current source)
Range Resolution Accuracy Current Source

20ohm 1 mili-ohm ±0.03% +1 10mA

200ohm 10 mili-ohm ±0.03%+ 1 10mA
2Kohm 0.1ohm ±0.03% +1 lmA
20Kohm lohm ±0.03%+1 0.1mA
* Conversion rate : 2.5, 5, 10 reading/sec
* Digital output : 16 channel TTL compatible 8.0mA sink and 0.4 mA driver
General :
* Power consumption : +5V, 390mA; +12V, 210mA typical

* Digital output connecter: 20 pin flat cable connector with +5V, +12V, ground
* I/O base address : &H200-&H3F0 (factory setting is &H230)
* Operating temperature : 0 – 50°C
* Storage temperature : -20 – 65°C
* Weight : 290gm

Add to cart

PCL-M10 – 3M – Industrial Accelerometer, 80mV/g

252,00 € Excl. VAT

Industrial Accelerometer Sensitivity: ±80 mV/g Sensing Range: 1~10kHz Direct connection with WISE-750

Add to cart

PCLD – 7216 – I/O MODULE CARR.BORD 16CH.

175,00 € Excl. VAT

Features Optically isolated inputs and outputs between computer and field devices Channel status reflected by on-board LED for easy monitoring On-board fuse protection Specifications

Add to cart

Cart

Cart

Vendor Advantech AE.

PCL-839 – HIGH SPEED STEP MOTOR CONTROL.

Introduction

Features of PCL-839 :

Applications

PCL-844 – 8 Port Intelligent RS-232 Card

PCL-846A – 4 Port RS-422/485 Card Isolat.

PCL-847A – 4 Port RS-422/485 Card

Features PCL-847A :

Introduction:

Specifications PCL-847A :

PCL-847B – 4 Port RS-422/485 Card SurgeP

Features PCL-847B:

Introduction PCL-847B:

PCL-848A – IEEE-488 CONTROLLER

General Information PCL-848A

The key features of this interface card include (PCL-848A) :

PCL-849A – 4 Port RS-232 Interface Card

Features PCL-849A:

Specifications PCL-849A :

PCL-860 – 4 1/2 DIGIT VOLTMETER (Rev A2)

Introduction

1.2. Specifications PCL-860

PCL-M10 – 3M – Industrial Accelerometer, 80mV/g

PCLD – 7216 – I/O MODULE CARR.BORD 16CH.

Cart