Vendor Advantech AE.
Showing 1–10 of 14 results
-
EKI-1121L – 1 Port Programmable Device Server CPU ARM7
204,00 € Excl. VATAdd to cartFeatures EKI-1121L :
√ARM7 32-bit 80MHz processor
√ 8MB Flash ROM on board
√16MB SDRAM
√ 2 x 10/100 Mbps Ethernet ports for LAN redundancy
√ 1 or 2 software selectable RS-232/422/485 serial ports
√ 50 bps to 921.6 kbps baud rate
√ Built-in real-time clock (RTC)
√ Class I, Division 2 certification
√ Pre-installed Linux Kernel 2.4 platformIntroduction :
EKI-1121L and EKI-1122L are RISC-based embedded communication controllers which provide dual auto-sensing 10/100 Mbps Ethernet ports for network redundancy and one or
two software-selectable RS-232/422/485 serial ports. The EKI-1121L and EKI-1122L use the ARM7 RISC CPU which is a powerful computing engine to fulfill data compression or
protocol conversion requirements. The built-in 8 MB flash ROM and 16 MB SDRAM provide user enough storage to run their specific applications.Specifications of EKI-1121L :
System
√ CPU ARM7 32-bit RISC CPU, 80 MHz
√ Flash 8 MB
√ SDRAM 16 MB
√ OS (pre-installed) uClinux
√ Console Port RS-232, 3-wire (Tx, Rx, GND) pin-header
√ Other RTC, watchdog timerEthernet Interface
√ LAN 2 x auto-sensing 10/100 Mbps ports
√ Connector RJ-45
√ Protection 1.5 kV magnetic isolation protection
Serial Interface
√ Serial Standards Software selectable RS-232/422/485 ports
√ Connectors D-sub 9 male
√ Protection 15 kV ESD protection for all signals
Serial Parameters
√ Data Bits 5, 6, 7, 8
√ Stop Bits 1, 1.5, 2
√ Parity None, Even, Odd, Space, Mark
√ Flow Control RTS/CTS, XON/XOFF, automatic RS-485 data flow
control
√ Baud Rate 50 bps to 921.6 kbpsSerial Signals
√ RS-232 TxD, RxD, DTR, DSR, RTS, CTS, DCD, RI, GND
√ RS-422 TxD+, TxD-, RxD+, RxD-, GND
√ RS-485 Data+, Data-, GND
LEDs
√ System OS ready, power 1 and power 2 ready
√ LAN Speed (10/100 Mbps), link/active (on connector)
√ Serial TxD, RxDMechanics
√ Dimensions 37 x 140 x 95 mm (W x H x D)
√ Housing Metal
√ Weight 600g
√ Mounting DIN-rail, wall
Power Requirements
√ Input Voltage 12 ~ 48 VDC, redundant dual inputs
√ Power Consumption 2.5 W
Software (uClinux)
√ Kernel Version 2.4.31
√ Protocol Stack TCP, UDP, IPv4, ICMP, ARP, SNMP V1, HTTP, DHCP,
NTP, NFS, SMTP, Telnet, FTP, PPP, PPPoE
√ File System ROMFS/JFFS2
√ System Utility busybox, telnet, ftp, sash, tftp
√ Daemon pppd, snmpd, telnetd, inted, ftpd, boa
√ Linux Tool Chain Arm-elf-gcc: C/C++ PC Cross Compiler
√ uClibc POSIX Standard Library -
EKI-1122L – 2 Port Programmable Device Server CPU ARM7
248,00 € Excl. VATAdd to cartFeatures EKI-1121L :
√ARM7 32-bit 80MHz processor
√ 8MB Flash ROM on board
√16MB SDRAM
√ 2 x 10/100 Mbps Ethernet ports for LAN redundancy
√ 1 or 2 software selectable RS-232/422/485 serial ports
√ 50 bps to 921.6 kbps baud rate
√ Built-in real-time clock (RTC)
√ Class I, Division 2 certification
√ Pre-installed Linux Kernel 2.4 platformIntroduction :
EKI-1121L and EKI-1122L are RISC-based embedded communication controllers which provide dual auto-sensing 10/100 Mbps Ethernet ports for network redundancy and one or
two software-selectable RS-232/422/485 serial ports. The EKI-1121L and EKI-1122L use the ARM7 RISC CPU which is a powerful computing engine to fulfill data compression or
protocol conversion requirements. The built-in 8 MB flash ROM and 16 MB SDRAM provide user enough storage to run their specific applications.Specifications of EKI-1122L :
System
√ CPU ARM7 32-bit RISC CPU, 80 MHz
√ Flash 8 MB
√ SDRAM 16 MB
√ OS (pre-installed) uClinux
√ Console Port RS-232, 3-wire (Tx, Rx, GND) pin-header
√ Other RTC, watchdog timerEthernet Interface
√ LAN 2 x auto-sensing 10/100 Mbps ports
√ Connector RJ-45
√ Protection 1.5 kV magnetic isolation protection
Serial Interface
√ Serial Standards Software selectable RS-232/422/485 ports
√ Connectors D-sub 9 male
√ Protection 15 kV ESD protection for all signals
Serial Parameters
√ Data Bits 5, 6, 7, 8
√ Stop Bits 1, 1.5, 2
√ Parity None, Even, Odd, Space, Mark
√ Flow Control RTS/CTS, XON/XOFF, automatic RS-485 data flow
control
√ Baud Rate 50 bps to 921.6 kbpsSerial Signals
√ RS-232 TxD, RxD, DTR, DSR, RTS, CTS, DCD, RI, GND
√ RS-422 TxD+, TxD-, RxD+, RxD-, GND
√ RS-485 Data+, Data-, GND
LEDs
√ System OS ready, power 1 and power 2 ready
√ LAN Speed (10/100 Mbps), link/active (on connector)
√ Serial TxD, RxDMechanics
√ Dimensions 37 x 140 x 95 mm (W x H x D)
√ Housing Metal
√ Weight 600g
√ Mounting DIN-rail, wall
Power Requirements
√ Input Voltage 12 ~ 48 VDC, redundant dual inputs
√ Power Consumption 2.5 W
Software (uClinux)
√ Kernel Version 2.4.31
√ Protocol Stack TCP, UDP, IPv4, ICMP, ARP, SNMP V1, HTTP, DHCP,
NTP, NFS, SMTP, Telnet, FTP, PPP, PPPoE
√ File System ROMFS/JFFS2
√ System Utility busybox, telnet, ftp, sash, tftp
√ Daemon pppd, snmpd, telnetd, inted, ftpd, boa
√ Linux Tool Chain Arm-elf-gcc: C/C++ PC Cross Compiler
√ uClibc POSIX Standard Library -
PCI-1625 – 8-Port Intelligent RS-232 Card
365,00 € Excl. VATAdd to cartFEATURES PCI-1625:
√RISC processor (TMS320)
√1 MB SRAM
√PCI Specification 2.2 compliant
√Speed up to 921.6 kbps
√8-port RS-232
√I/O address automatically assigned by PCI Plug &Play
√OS supported: Windows 2000/XP
√Powerful and easy to use utility (ICOM tools)
√Link with OPT8FP peripherals up to 1200m (4000ft) from controller (RS-422)
√Universal PCI (Supports 3.3 V or 5 V PCI bus signal) -
-
PCL-721 – 32 Channel D/I Card
156,00 € Excl. VATAdd to cartIntroduction PCL-721 :
The PCL-721/723 is a 32/24-channel digital input card with independent
interrupt capabilities that allows the PCL-721/723 to work in the
background while the processor perform other jobs in the foreground. With
this feature, your system can do real-time Process monitoring without
polling its inputs, channel by channel.The PCL-721/723 has two modes: normal and interrupt. While it is set to
normal mode, the PCL-721/723 serves as a general purpose multi-channel
digital input card. However,if it is set to interrupt mode, then each channel
will generate an interrupt request to the PC, once the channel input has
changed.The 32digital input channels ofthe PCL-721 are divided into 4 groups. The
24 digital input channels of the PCL-723 are divided into 3 groups. Each
group handles8 digital input channels. There is a register that reflects the
interrupt status of each groups. Users can first read this register to check
which group caused the interrupt, then by reading the 8channels’ status of
that group, you can easily find which channel generated the interrupt. This
two-pass feature saves lot of time to determine which service routine should
be executed in your ISR (Interrupt Service Routine).The PCL-721/723 is easy to configure. No switch or jumper settings are
needed (except the I/O base address). The IRQ level, individual channel’s
trigger mode (rising or falling edge), and interrupt mask (enable or disable)
are all software programmable -
PCL-731 – 48bit Digital I/O Card
131,00 € Excl. VATAdd to cartFeatures:
• 48 digital I/O lines
• Emulates 8255 PPI mode 0
• Buffered circuits for higher driving capacity than the 8255
• Interrupt handling
• Output status readback
• Pin compatible with Opto-22 I/O module racksIntroduction :
The PCL-731 offers 48 programmable digital I/O lines. Each port
emulates the operation of an 8255 Programmable Peripheral
Interface (PPI) chip in mode 0, but provides a higher driving capacity
than the 8255.
The card’s DIO ports are combined into 8-bit ports, six for the
PCL-731. You can configure each port individually by software for
either input or output. The card can directly interface with SSR
module carrier boards through a 50-pin Opto-22 compatible
connector.
The PCL-731 is a low-cost alternative of the PCL-722. Like the
PCL-722 it provides a readback feature which lets you monitor the
status of the output by reading back the output portApplications
• Digital I/O control
• Industrial monitoring and control
• Interfacing with parallel I/O devices
• Interfacing with Opto-22 compatible I/O module racks
Specifications
• I/O lines: 48
• Programming mode: 8255 PPI mode 0
• Interrupt: Bit 0 of one port can generate an interrupt to
IRQ 2~15
• Interrupt triggering: Rising or falling edge triggering, jumperselectable
• Digital output: Logic 0: 0.4 V max. @ 24 mA (sink)
Logic 1: 2.4 V min. @ 15 mA (source)
• Digital input: Logic 0: 0.4 V max.
Logic 1: 2.4v minGeneral PCL-731
• Power consumption:+5 V @ 0.5 A typical
+5 V @ 0.8 A max.
• Operating temperature: 0 ~ +60° C (32 ~ 140° F)
• Storage temperature: -20 ~ +70° C (-4 ~ 158° F)
• Operating humidity: 5 ~ 95% RH non-condensing (refer to IEC
68-2-3)
• Connectors: 2×50-pin male ribbon-cable connectors
• Dimensions: 185 mm (L) x 100 mm (H) (7.3″ x 3.9″)Ordering Information
PCL-731: 48-bit digital I/O card and manual
PCL-10150-1.2: 50-pin flat cable, 1.2 m
PCLD-782B: 24/16-ch. opto-isolated digital input board
PCLD-785B: 24/16-ch. relay output board
PCLD-7216: 16-ch. carrier board for SSR I/O modules
PCLD-885: 16-ch. power relay (Form A) output board
PCLS-OCX: ActiveX Control for data acquisition and control.
ADAM-3950: 50-pin flat cable wiring terminal for DIN-rail -
PCL-733 – 32Ch.Isolated DI Card W.Inter.
212,00 € Excl. VATAdd to cartFeatures PCL-733 :
√ 32 isolated, digital input channels PCL-733
√ High-voltage isolation (2,500 VDC)
√ Interrupt capacity
√ D-type connectors for isolated input channels
√ Reverse voltage protection for isolated input channels (up to 24 VDCSpecifications PCL-733 :
Isolated Digital Input
√ Input Channels 32 (16-ch/group)
√ Input Voltage Logic 0: PCI-1733: 2 V max., PCL-733: 1 V max.
Logic 1: 5 V min.
PCI-1733: 30 V max., PCL-733: 24 V max.√Interrupt Capable Ch. 4 for PCI-1733, 2 for PCL-733
√ Isolation Protection 2,500 VDC
√ Opto-Isolator Response PCL-733: 100 µs, PCI-1733: 25 µs
√ Input Resistance PCI-1733: 2.7 kΩ @ 1 W
: 1.2 kΩ @ 0.5 W
General
√ Bus Type PCI-1733: PCI V2.2, : ISA
√ I/O Connectors 1 x 37-pin D-type female
√ Dimensions (L x H) : 185 x 100 mm (7.3” x 3.9”)
: 175 x 100 mm (6.9” x 3.9”)
√ Power Consumption
: Typical: +5 V @ 320 mA
Max: +5 V @ 500 mA
PCI-1733: Typical: 5V @ 200 mA, 12 V @ 50 mA
Max: 5V @ 350 mA, 12 V @ 75 mA
√ Operating Temperature 0 ~ 60° C (32 ~ 140° F)
√ Storing Temperature PCL-733: -20 ~ 70° C (-4 ~ 158° F)
PCI-1733: -25 ~ 85° C (-13 ~ 185° F)
√ Storing Humidity 5 ~ 95% RH, non-condensing (IEC 68-2-3)Ordering Information
√ PCI-1733 32-channel isolated PCI digital input card, manual and
driv er CD-ROM (cable not included)
√ 32-channel isolated digital input card, manual and
driver CD-ROM (cable not included)
√ PCLD-780 Universal screw terminal board
√ PCLD-880 Universal screw terminal board
√ ADAM-3937 DB37 wiring terminal for DIN-rail mounting
√ PCL-10137-1 DB37 cable, 1m
√ PCL-10137-2 DB37 cable, 2m
√ PCL-10137-3 DB37 cable, -
PCL-752 – Intelligent SYSTEM MONITORCard
383,00 € Excl. VATAdd to cartFeatures PCL-752
• Monitoring +5VDC,-5VDC, +12VDC., -12VDC of ISA bus voltage
• Three external voltage sense inputs
• Three fan sense inputs for fan speed monitoring
• Three temperature sense inputs
• Two “power good” signal inputs for power supply monitoring
• Two isolated digital inputs
• Three relay outputs for alarm connection
• Watchdog timer for detecting system CPU operation
• One serial port can be set as a RS-232 or RS-485 port, supporting
modem output for connection to remote system center
• Three configurable alarm levels: Critical, major, minor
• Audible alarm with three sound effects
• On-board battery backup ensuring normal card operation in case of
• system power failure
• Built-in watchdog timer for self-detection ensuring reliable card
operation
• Compact half-sized card dimensions -
PCL-839 – HIGH SPEED STEP MOTOR CONTROL.
576,00 € Excl. VATAdd to cartIntroduction
PCL-839 is a high-speed three-axis stepping motor control card that
simplifies stepping motor control, giving you added performance from
your stepping motors.Three-axis control
The PCL-839 has three single-chip pulse generators on-board, which
enables the simultaneous and independent control of three axis. The
PCL-839 provides digital pulse and directional control (+ and -) for each
stepping motor axis.User-friendly interface
The PCL-839 has been designed to act as a user-friendly solution for
your stepping motor control applications. Programming the PCL-839 is
very easy. ‘C’ Libraries are provided and they contain all the command
functions needed for total control of your stepping motors.Stand-alone interpreter
A stand-alone, non-resident command interpreter, PROGg39.EXE, can
also be used to control your stepping motors without any programming.
Digital I/O
The PCL-839 features 16 digital inputs and 16 digital outputs for general
I/O use (on/off control etc.).
Isolation protection
The PCL-839’s PULSE and DIRECTION outputs and five limits input
switches are isolated from the PC side.Features of PCL-839 :
· Three on-board pulse generators that enables simultaneous independent
control of three stepping motors
· Two operating modes – two-pulse (+ and – direction pulse) or one-pulse
(pulse-direction) mode
· Programmable step rate from 1 to 16k pps (pulses per second).
· Programmable initial speed, final speed and time duration. Automatic
trapezoidal acceleration/deceleration Tamping is performed
· 16 I/O TTL compatible channels
· All inputs/outputs are optically isolated, providing 500VDC isolation
protection
· ‘C’ libraries containing device drivers provided
· Command Interpreter provided that eases learning the PCL-839 command
setApplications
· Precise X-Y-Z position control
· Precise rotation control
· Robotics and assembly equipment
· Other stepping-motor applicationsGeneral
· Power consumption: 300mA, +5VDC
· Connector: 37-pin D-type connector
· Board dimensions: 183.5 mm x 99.06 mm
· Operatingtemperature:0 to70°C -
PCL-847A – 4 Port RS-422/485 Card
180,00 € Excl. VATAdd to cartFeatures PCL-847A :
• Four independent RS-422/485 serial ports
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS control PCL-847AIntroduction:
PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires.Specifications PCL-847A :
• Ports: 4
• UART: 4 x 16C550 with 16-byte FIFO
• Speed: 50 ~ 921.6 Kbps
• Parity: none, even, odd
• Signal support:
TxD+, TxD-, RxD+, RxD-, CTS+, CTS-, RTS+ and RTS-
• I/O address: From 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Isolation voltage: 1000 VDC (PCL-846A/846B only)
• Surge protection: 3000 VDC (PCL-846B/847B)
• Power consumption: +5 V @ 250 mA typical, 500 mA max.
• Cables: 30-cm male DB-37 to four male DB-9 (DTE)
• Operating temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage temperature: -25 ~ 80° C (-13 ~ 176° F)
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″)
