PCL-839 – HIGH SPEED STEP MOTOR CONTROL.
576,00 € Excl. VAT
Introduction
PCL-839 is a high-speed three-axis stepping motor control card that
simplifies stepping motor control, giving you added performance from
your stepping motors.
Three-axis control
The PCL-839 has three single-chip pulse generators on-board, which
enables the simultaneous and independent control of three axis. The
PCL-839 provides digital pulse and directional control (+ and -) for each
stepping motor axis.
User-friendly interface
The PCL-839 has been designed to act as a user-friendly solution for
your stepping motor control applications. Programming the PCL-839 is
very easy. ‘C’ Libraries are provided and they contain all the command
functions needed for total control of your stepping motors.
Stand-alone interpreter
A stand-alone, non-resident command interpreter, PROGg39.EXE, can
also be used to control your stepping motors without any programming.
Digital I/O
The PCL-839 features 16 digital inputs and 16 digital outputs for general
I/O use (on/off control etc.).
Isolation protection
The PCL-839’s PULSE and DIRECTION outputs and five limits input
switches are isolated from the PC side.
Features of PCL-839 :
· Three on-board pulse generators that enables simultaneous independent
control of three stepping motors
· Two operating modes – two-pulse (+ and – direction pulse) or one-pulse
(pulse-direction) mode
· Programmable step rate from 1 to 16k pps (pulses per second).
· Programmable initial speed, final speed and time duration. Automatic
trapezoidal acceleration/deceleration Tamping is performed
· 16 I/O TTL compatible channels
· All inputs/outputs are optically isolated, providing 500VDC isolation
protection
· ‘C’ libraries containing device drivers provided
· Command Interpreter provided that eases learning the PCL-839 command
set
Applications
· Precise X-Y-Z position control
· Precise rotation control
· Robotics and assembly equipment
· Other stepping-motor applications
General
· Power consumption: 300mA, +5VDC
· Connector: 37-pin D-type connector
· Board dimensions: 183.5 mm x 99.06 mm
· Operatingtemperature:0 to70°C
2 in stock
Introduction
PCL-839 is a high-speed three-axis stepping motor control card that
simplifies stepping motor control, giving you added performance from
your stepping motors.
Three-axis control
The PCL-839 has three single-chip pulse generators on-board, which
enables the simultaneous and independent control of three axis. The
PCL-839 provides digital pulse and directional control (+ and -) for each
stepping motor axis.
User-friendly interface
The PCL-839 has been designed to act as a user-friendly solution for
your stepping motor control applications. Programming the PCL-839 is
very easy. ‘C’ Libraries are provided and they contain all the command
functions needed for total control of your stepping motors.
Stand-alone interpreter
A stand-alone, non-resident command interpreter, PROGg39.EXE, can
also be used to control your stepping motors without any programming.
Digital I/O
The PCL-839 features 16 digital inputs and 16 digital outputs for general
I/O use (on/off control etc.).
Isolation protection
The PCL-839’s PULSE and DIRECTION outputs and five limits input
switches are isolated from the PC side.
Features of PCL-839 :
· Three on-board pulse generators that enables simultaneous independent
control of three stepping motors
· Two operating modes – two-pulse (+ and – direction pulse) or one-pulse
(pulse-direction) mode
· Programmable step rate from 1 to 16k pps (pulses per second).
· Programmable initial speed, final speed and time duration. Automatic
trapezoidal acceleration/deceleration Tamping is performed
· 16 I/O TTL compatible channels
· All inputs/outputs are optically isolated, providing 500VDC isolation
protection
· ‘C’ libraries containing device drivers provided
· Command Interpreter provided that eases learning the PCL-839 command
set
Applications
· Precise X-Y-Z position control
· Precise rotation control
· Robotics and assembly equipment
· Other stepping-motor applications
General
· Power consumption: 300mA, +5VDC
· Connector: 37-pin D-type connector
· Board dimensions: 183.5 mm x 99.06 mm
· Operatingtemperature:0 to70°C
Shipping Policy
Shipping Worldwide
Refund Policy
Refunds
Returns are only accepted if product are not as specified or have any defects.Once your return is received and inspected, we will send you an email to notify you that we have received your returned item. We will also notify you of the approval or rejection of your refund.
If you are approved, then your refund will be processed, and a credit will automatically be applied to your credit card or original method of payment, within a certain amount of days.
Late or missing refunds
If you haven’t received a refund yet, first check your bank account again.
Then contact your credit card company, it may take some time before your refund is officially posted.
Next contact your bank. There is often some processing time before a refund is posted.
If you’ve done all of this and you still have not received your refund yet, please contact us at {email address}.
Sale items
Only regular priced items may be refunded. Sale items cannot be refunded.
Exchanges
We only replace items if they are defective or damaged.
Gifts
If the item was marked as a gift when purchased and shipped directly to you, you’ll receive a gift credit for the value of your return. Once the returned item is received, a gift certificate will be mailed to you.
If the item wasn’t marked as a gift when purchased, or the gift giver had the order shipped to themselves to give to you later, we will send a refund to the gift giver and they will find out about your return.
Shipping returns
To return your product, you should mail your product.
You will be responsible for paying for your own shipping costs for returning your item. Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
Depending on where you live, the time it may take for your exchanged product to reach you may vary.
If you are returning more expensive items, you may consider using a trackable shipping service or purchasing shipping insurance. We don’t guarantee that we will receive your returned item.
Need help?
Cancellation / Return / Exchange Policy
Overview
Our refund and returns policy lasts 30 days. Returns are only accepted if product are not as specified or have any defects.If 30 days have passed since your purchase, we can’t offer you a full refund or exchange.
To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.
Several types of goods are exempt from being returned. Perishable goods such as food, flowers, newspapers or magazines cannot be returned. We also do not accept products that are intimate or sanitary goods, hazardous materials, or flammable liquids or gases.
Additional non-returnable items:
- Gift cards
- Downloadable software products
- Some health and personal care items
To complete your return, we require a receipt or proof of purchase.
Please do not send your purchase back to the manufacturer.
There are certain situations where only partial refunds are granted:
- Book with obvious signs of use
- CD, DVD, VHS tape, software, video game, cassette tape, or vinyl record that has been opened.
- Any item not in its original condition, is damaged or missing parts for reasons not due to our error.
- Any item that is returned more than 30 days after delivery
General Inquiries
There are no inquiries yet.
Related products
-
PCL-847A – 4 Port RS-422/485 Card
180,00 € Excl. VATAdd to cartFeatures PCL-847A :
• Four independent RS-422/485 serial ports
• Transmission speeds up to 921.6 Kbps
• Independent/shared IRQ settings between each of the 4 serial ports
• Wide IRQ selection: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Supports standard DOS COM1, COM2, COM3, and COM4
• Supports DOS/Windows 3.1 (PC-ComLIB), Windows 95/98,
Windows NT (ICOM Utility)
• Provides 1000 VDC isolation (PCL-846A/846B only)
• Provides 3000 VDC surge protection (PCL-846B/847B)
• Space reserved for termination resistors
• Supports 2 wire or 4 wire operation
• Supports Tx, Rx, RTS, and CTS signals
• Automatic RS-485 data flow control or RTS control PCL-847AIntroduction:
PCL-846/847 series cards provide four independent RS-422/485
serial ports on a card. Each port has a 16C550 UART with an on-chip
16-byte FIFO buffer for reliable, high-speed serial I/O. The UART
buffers data into 16-byte packets before putting it on the bus. This
drastically reduces the CPU load and avoids data loss when the
system is busy and cannot process the interrupt quickly. The UART
is especially useful for high speed serial I/O under Windows.
PCL-846 cards differ from PCL-847 cards in that they utilize
on-board optical isolators to protect your PC and equipment against
damage from ground loops, increasing system reliability in harsh
environments. To further increase reliability, PCL-846B/847B cards
include surge protection technology, protecting your system from
abrupt high voltage surges (up to 3000 V) such as those caused by
lightning during thunderstorms.An RS-485 Network with Automatic Data Flow Control
Using RS-232 Software
The RS-485 mode automatically senses the direction of incoming
data and switches its transmission direction accordingly. This feature
makes your network look and act just like an RS-232 network.
Application software written for half duplex RS-232 can be used
without modification. Moreover, you can simply and quickly build an
RS-485 network with just two wires.Specifications PCL-847A :
• Ports: 4
• UART: 4 x 16C550 with 16-byte FIFO
• Speed: 50 ~ 921.6 Kbps
• Parity: none, even, odd
• Signal support:
TxD+, TxD-, RxD+, RxD-, CTS+, CTS-, RTS+ and RTS-
• I/O address: From 200H to 3F8H
• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15
• Isolation voltage: 1000 VDC (PCL-846A/846B only)
• Surge protection: 3000 VDC (PCL-846B/847B)
• Power consumption: +5 V @ 250 mA typical, 500 mA max.
• Cables: 30-cm male DB-37 to four male DB-9 (DTE)
• Operating temperature: 0 ~ 60° C (32 ~ 140° F)
• Storage temperature: -25 ~ 80° C (-13 ~ 176° F)
• Dimensions: 185 mm x 100 mm (7.3″ x 3.9″) -
POC-174CB-AC- A Point-of-Care Terminal
860,00 € – 882,00 € Excl. VATSelect optionsThe POC-174 is a medical-grade Point-of Care Panel PC with a 17” display optimized for minimal power leakage and low EMI. It is approved according to EN60601-1 and UL2601-1 standards. This certifies that there is no interference with medical equipment that can pose a health risk for patients. The POC-174 has also been also approved with IP65/NEMA 4 and IPX1 for dust-resistance and water spills. Like the other products in the POC series, the POC-174 has all the characteristics needed for use in critical medical environments. Its high brightness, resolution, and contrast ratio LCD display is especially suitable for medical diagnosis and treatment methods like: CT diagnosis, electrical X-ray, PACS and DICOM. With a wide range of I/O options, the POC series supply full connectivity, and offer the most secure and practical healthcare terminals for patients and practitioners.
Manufacturer’s warranty has expired.
Specifications POC-174CB-AC-
General
§ Dimension (W x H x D) 437 x 377 x 131 mm (17.20″ x 14.84″ x 5.15″)
§ Weight 12 kg (26.5 lb)
§ Power Supply AC model: 180 watt
Input voltage: 100 ~ 240 VAC, 4 A max.@ 50 ~ 60 Hz
Output voltages: +5 V @ 12 A, +12 V @ 12 A
+3.3 V @ 16.8 A, +5 Vsb @ 2.0 A, -12 V @ 0.8 A DC model:
Input voltage: +24 VDC, 7.5 A max
Output voltage: +5 V @ 10 A, +12 V @ 4 A,
-12 V @ 1 A, +3.3 V @ 8 A, +5 Vsb @ 0.75 A
§ Cooling Fan (L x W x H) 60 x 60 x 10 mm (2.4″ x 2.4″ x 2.4″)
§ Front Panel IP65/NEMA compliant
Standard PC Functions
§ CPU Intel® Pentium® 4 Mobile
§ Memory 2 x 184-pin DIMM socket accepts up to 2 GB DDR333/266 DRAM 1GB installed)
§ HDD 1 x 2.5″ IDE HDD
§ FDD 1.44 MB
§ CD ROM Slim type (Optional: CD-RW/DVD-ROM)
§ PCMCIA 2x Type II
§ I/O Ports &Speakers 4 x Serial ports: 3 x RS-232, 1 x RS-232/422/485;
1 x Parallel port
2 x USB ports
1 x PS/2 mouse and keyboard interface
1x Mic-in
1 x Line-in
1 x Speaker-out
2 x 1 W speakers
§ Network (LAN) 2 x 10/100Base-T Ethernet interface
§ Bus Expansion 1 x PCI 2.2 expansion slot
§ Optional 802.11b wireless antenna with wireless LAN PCMCIA module
Display Specifications
§ Display Type 17″ TFT LCD
§ Max.Resolution 1280 x 1024
§ Colors 16.7 M (8 bits/color)
§ Dot Size (mm) 0.264 x 0.264
§ Viewing Angle 170°
§ Luminance 250 cd/m2
§ Contrast Ratio 600 : 1
§ LCD MTBF 50,000 hours
§ Backlight Lifetime 40,000 hours
Specifications Cont.
Environmental Specifications
§ Temperature 0 ~ 40° C
§ Relative Humidity 10 ~ 95% @ 40° C (non-condensing)
§ Shock 50 G peak acceleration (11 msec duration)
§ Power MTBF 100,000 hrs
§ Certifications CE, FCC, VCCI, BSMI approved
§ AC Model UL60950, UL60601-1, EN60950, EN60601-1 approved
§ DC Model FCC, UL60601-1, EN60601-1 approved
Mounting
- Vesa 75 x 75 mm, 100 x 100 mm
-
AWS-825P
2.650,00 € Excl. VATAdd to cartFeatures of AWS-825P:
√9-slot, 15″ TFT LCD workstation AWS-825P
√Resolution: 1024 x 768
√Two-piece design: integrated or separated LCD panel & control chassis
√Built-in touchpad, USB port and floppy drive on front panel
√Designed for simple maintenance with hinged rear door for easy access
√Vibration protection up to 1G
√Heavy-duty stainless steel chassis with aluminum front panel
√Hard anodic coating to prevent panel abrasion and acid corrosion
√Front panel is NEMA4/IP65 compliant AWS-825PSpecifications:
General
Button Controls
Membrane Keypad 1 39 operating keys
Membrane Keypad 2 10 function keys
10 programmable macro function keys
OSD On front panel with backlight on/off switch
Touchpad On front panel
Certifications BSMI, CE, CCC, and FCC class A
Connectors 1 x front-accessible 6-pin PS/2 with dust-protection door for keyboard
Cooling System 1 x 86 CFM fan
Dimensions (W x H x D) 482 x 356 x 229 mm (18.98″ x 14.0″ x 9″)
Enclosure Aluminum
Disk Drive Bay Supports one 3.5″ FDD, one 3.5″ HDD & one slim CD-ROM (HDD and CD-ROM optional)
LED Indicators Power on/off and HDD activity
Mounting 19″ rack
LCD Display
Backlight Life 50,000 hours
Display Size 15″
Display Type XGA TFT LCD
Luminance 350 cd/m2
Max. Colors 262 K
Max. Resolution 1024 x 768
Viewing Angle (H/V°) 120/100Introduction AWS-825P :
AWS-8259 is an industrial workstation with 9-slot expansion capability. Featuring a 15″ detachable display module, the AWS-8259 has a rugged yet flexible design for factory floor
applications. Its 15″ high-brightness 1024 x 768 LCD fulfills the needs for large information viewing. In addition, the display module can be easily separated for maintenance.
With waterproof character keypads & touchpad features, an additional keyboard or mouse is not needed for operation. The standard 8U size can easily be installed in either racks or
mounted in panels.